View TDA5153AG_465730.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
DATA SHEET
TDA5153 Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
Preliminary specification File under Integrated Circuits, IC11 1997 Jul 02
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
CONTENTS 1 2 3 4 5 6 7 8 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 8.10 8.10.1 8.10.2 8.10.3 8.10.4 8.10.5 8.10.5.1 8.10.5.2 8.10.5.3 8.10.6 8.10.7 8.10.8 8.10.9 8.10.10 8.11 8.12 9 10 11 12 13 14 15 16 17 FEATURES APPLICATIONS GENERAL DESCRIPTION ORDERING INFORMATION QUICK REFERENCE DATA BLOCK DIAGRAM PINNING FUNCTIONAL DESCRIPTION Read mode Write mode Sleep mode Standby mode Active mode Bi-directional serial interface Addressing Programming data Reading data Operation of the serial interface Configuration Power control Head select Servo write Test MR head test Temperature monitor Thermal asperity detector Write amplifier programmable capacitors High frequency gain attenuator pole register High frequency gain boost register Settle pulse Address registers Head unsafe HUS survey LIMITING VALUES HANDLING THERMAL RESISTANCE RECOMMENDED OPERATION CONDITIONS CHARACTERISTICS PACKAGE OUTLINE SOLDERING DEFINITION LIFE SUPPORT APPLICATIONS
TDA5153
1997 Jul 02
2
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
1 FEATURES 3 GENERAL DESCRIPTION
TDA5153
* Designed for 4 (TDA5153BG) or 6 dual-stripe MR-read/inductive write heads * Current bias-current sense architecture * Single supply voltage (5.0 V 10%); a separate write drivers supply pin can be biased from VCC to 8 V +10% * MR elements connected to ground (GND) * Equal bias currents in the two MR stripes of each head * On-chip AC couplings eliminate MR head DC offset * 3-wire serial interface for programming * Programmable high-frequency zero-pole gain boost * Programmable write driver compensation capacitance * Programmable MR bias currents and write currents * 1-bit programmable read gain * Sleep, standby, active and test modes available * Measurement of head resistances in test mode * In test mode, one MR bias current may be forced to a minimum current * Short write current rise and fall times with near rail-to-rail voltage swing * Head unsafe pin for signalling of abnormal conditions and behaviour * Low supply voltage write-current inhibit (active or inactive) * Supports servo writing * Provides temperature monitor * Thermal asperity detection with programmable threshold level * Requires only one external resistor. 2 APPLICATIONS
The 5.0 V pre-amplifier for HDD described here is designed for five terminals, dual stripe Magneto-Resistive (MR)-read/inductive-write heads. The disks of the disk drive are connected to ground. To avoid voltage break-through between the heads and the disk, the MR elements of the heads are also connected to ground. The symmetry of the dual-stripe head-amplifier combination automatically distinguishes between the differential signals such as signals and the common-mode effects like interference. The latter are rejected by the amplifier. The IC incorporates read amplifiers, write amplifiers, serial interface, digital-to-analog converters, reference and control circuits which operate on a single supply voltage of 5 V 10%. The output drivers have a separate supply voltage pin which can be connected to a higher supply voltage of up to 8 V +10%. The complementary output stages of the write amplifier allow writing with near rail-to-rail peak voltages across the inductive write head. The read amplifier has a low input impedance. The DC offset between the two stripes of the MR head is eliminated using on-chip AC coupling. Fast settling features are used to keep the transients short. As an option, the read amplifier may be left biased during writing so as to reduce the duration of these transients even more. Series inductance in the leads between the amplifier and MR heads influences the bandwidth which can be compensated by using a programmable high-frequency gain-boost (HF zero). HF noise and bandwidth can be attenuated using a programmable high-frequency gain-attenuator (HF pole). On-chip digital-to-analog converters for MR bias currents and write currents are programmed via a 3-wire serial interface. Head selection, mode control, testing and servo writing can also be programmed using the serial interface. In sleep mode the CMOS serial interface is operational. Figure 1 shows the block diagram of the device.
* Hard Disk Drive (HDD). 4 ORDERING INFORMATION TYPE NUMBER TDA5153X TDA5153AG; TDA5153BG
PACKAGE NAME - LQFP48 naked die plastic low profile quad flat package; 48 leads; body 7 x 7 x 1.4 mm DESCRIPTION VERSION - SOT313-2
1997 Jul 02
3
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
5 QUICK REFERENCE DATA SYMBOL VCC VCC(WD) F Vnir Gv(dif) PARAMETER supply voltage write drivers supply voltage noise figure RMR = 28 ; IMR = 10 mA; Tamb = 25 C; f = 20 MHz CONDITIONS MIN. 4.5 VCC - - TYP. 5.0 8.0 3.0 0.9
TDA5153
MAX. 5.5 8.8 3.2 1.0
UNIT V V dB nV/Hz
input referred noise voltage; see RMR = 28 ; IMR = 10 mA; note 3 in Chapter 13 Tamb = 25 C; f = 20 MHz differential voltage gain from head inputs to RDx, RDy; RMR = 28 ; IMR = 10 mA d4 = logic 0 d4 = logic 1
- - - - - - -
160 226 220 45 25 80 50
- - - - - - - MHz dB dB dB dB
B-3 db CMRR PSRR
-3 dB frequency bandwidth common mode rejection ratio; RMR mismatch <5% power supply rejection ratio (input referred); RMR mismatch <5% rise/fall times (10% to 90%)
upper bandwidth without gain boost (4 nH lead inductance) IMR = 10 mA; f < 1 MHz IMR = 10 mA; f < 100 MHz f < 1 MHz f < 100 MHz Lh = 150 nH; IWR = 35 mA; f = 20 MHz VCC(WD) = 8.0 V VCC(WD) = 6.5 V
tr, tf
- - 5 20 -
- - - - -
1.8 2.1 20.5 51 25
ns ns mA mA MHz
IMR(PR)
programming MR bias current
Rext = 10 k Rext = 10 k
IWR(PR)(b-p) programming write current range (base-to-peak) fSCLK serial interface clock rate
1997 Jul 02
4
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
6 BLOCK DIAGRAM
VCC 11 WDlx WDly IWDlx(1) IWDly(1) 2 3 WRITE DRIVER INPUT FF 6(3) VCC(WD) (5 to 8 V) 48
TDA5153
handbook, full pagewidth
TDA5153
6(3) 15(2), 20, 26, 33, 39, 44(2) 14(2), 19, 25, 32, 38, 43(2) nWy nWx
HUS
1
HEAD UNSAFE INDICATOR 6(3) LOW SUPPLY VOLTAGE INDICATOR WRITE CURRENT SOURCE WRITE DRIVER AND READ PREAMP (6x)(3)
Rext
12
VOLTAGE REFERENCE +VCC TAS DETECTOR SERIAL INTERFACE 20 k 4 5 3 6 head select 6(3)
R/W SCLK SEN SDATA
4 7 5
5 4 4 9 RDx RDy 10
RMR CURRENT SOURCE 6(3) 18(2), 23, 29, 36, 42, 47(2) 17(2), 22, 28, 35, 41, 46(2) 16(2), 21, 27, 34, 40, 45(2) nRy
6(3)
nGND
6(3) 8, 13
nRx
MGK422
GND n Pin numbers correspond to TDA5153AG and TDA5153BG only. See Fig.3 and Chapter 7 for pinning of TDA5153X. (1) Only available on naked die. (2) Absent on TDA5153BG (4 channel version). (3) 4 on TDA5153BG.
Fig.1 Block diagram.
1997 Jul 02
5
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
7 PINNING PIN SYMBOL TDA5153AG TDA5153BG TDA5153X HUS WDIx WDIy IWDIx IWDIy R/W SEN SDATA SCLK GND1 RDx RDy GND3 VCC Rext GND2 0Wx 0Wy 0Rx 0GND 0Ry n.c. n.c. n.c. n.c. n.c. 1Wx 1Wy 1Rx 1GND 1Ry n.c. 2Wx 2Wy 2Rx 2GND 2Ry n.c. 1 2 3 - - 4 5 6 7 8 9 10 - 11 12 13 14 15 16 17 18 - - - - - 19 20 21 22 23 24 25 26 27 28 29 30 1 2 3 - - 4 5 6 7 8 9 10 - 11 12 13 - - - - - 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 - - - - - 22 23 24 25 26 - 27 28 29 30 31 - head unsafe output write data input (differential; voltage input) write data input (differential; voltage input) write data input (differential; current input) write data input (differential; current input) read/write (read = HIGH; write = LOW) serial bus enable serial bus data serial bus clock ground connection 1 read data output (differential x - y) read data output (differential x - y) ground connection 3 supply voltage 10 k external resistor ground connection 2 PAD DESCRIPTION
TDA5153
inductive write head connection for head H0 (differential x - y) inductive write head connection for head H0 (differential x - y) MR-read head connection for head H0 (differential x - y) ground connection for head H0 MR-read head connection for head H0 (differential x - y) not connected not connected not connected not connected not connected inductive write head connection for head H1 (differential x - y) inductive write head connection for head H1 (differential x - y) MR-read head connection for head H1 (differential x - y) ground connection for head H1 MR-read head connection for head H1 (differential x - y) not connected inductive write head connection for head H2 (differential x - y) inductive write head connection for head H2 (differential x - y) MR-read head connection for head H2 (differential x - y) ground connection for head H2 MR-read head connection for head H2 (differential x - y) not connected
1997 Jul 02
6
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
PIN SYMBOL TDA5153AG TDA5153BG TDA5153X n.c. 3Wx 3Wy 3Rx 3GND 3Ry n.c. 4Wx 4Wy 4Rx 4GND 4Ry 5Wx 5Wy 5Rx 5GND 5Ry n.c. n.c. n.c. n.c. n.c. VCC(WD) GND4 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 - - - - - 48 - 31 32 33 34 35 36 37 38 39 40 41 42 - - - - - 43 44 45 46 47 48 - - 32 33 34 35 36 - 37 38 39 40 41 42 43 44 45 46 - - - - - 47 48 not connected PAD DESCRIPTION
TDA5153
inductive write head connection for head H3 (differential x - y) inductive write head connection for head H3 (differential x - y) MR-read head connection for head H3 (differential x - y) ground connection for head H3 MR-read head connection for head H3 (differential x - y) not connected inductive write head connection for head H4 (differential x - y) inductive write head connection for head H4 (differential x - y) MR-read head connection for head H4 (differential x - y) ground connection for head H4 MR-read head connection for head H4 (differential x - y) inductive write head connection for head H5 (differential x - y) inductive write head connection for head H5 (differential x - y) MR-read head connection for head H5 (differential x - y); ground connection for head H5 MR-read head connection for head H5 (differential x - y) not connected not connected not connected not connected not connected supply voltage for the write drivers ground connection 4
1997 Jul 02
7
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
TDA5153
handbook, full pagewidth
48 VCC(WD)
41 4GND
46 5GND
38 4Wx
39 4Wy
44 5Wy
43 5Wx
45 5Rx
40 4Rx
42 4Ry
47 5Ry
37 n.c.
HUS
1
36 3Ry 35 3GND 34 3Rx 33 3Wy 32 3Wx
WDIx 2 WDIy 3 R/W 4 SEN 5 SDATA 6 SCLK 7 GND1 8 RDx 9 RDy 10 VCC 11 Rext 12
TDA5153AG
31 n.c. 30 n.c. 29 2Ry 28 2GND 27 2Rx 26 2Wy 25 2Wx
1Rx 21
1GND 22
GND2 13
0Wx 14
0Wy 15
0Rx 16
0GND 17
0Ry 18
1Wx 19
1Wy 20
1Ry 23
n.c. 24 37 n.c. n.c. 24
MGK424
handbook, full pagewidth
48 VCC(WD)
41 4GND
38 4Wx
39 4Wy
40 4Rx
42 4Ry
46 n.c.
45 n.c.
44 n.c.
43 n.c.
47 n.c.
HUS
1
36 3Ry 35 3GND 34 3Rx 33 3Wy 32 3Wx
WDIx 2 WDIy 3 R/W 4 SEN 5 SDATA 6 SCLK 7 GND1 8 RDx 9 RDy 10 VCC 11 Rext 12
TDA5153BG
31 n.c. 30 n.c. 29 2Ry 28 2GND 27 2Rx 26 2Wy 25 2Wx
1Rx 21
1GND 22
GND2 13
n.c. 14
n.c. 15
n.c. 16
n.c. 17
n.c. 18
1Wx 19
1Wy 20
1Ry 23
MGK420
Fig.2 Pin configurations.
1997 Jul 02
8
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
TDA5153
handbook, full pagewidth
VCC(WD)
5GND
4GND
5Wy
5Wx
4Wy
GND4 HUS WDIx WDIy IWDIx IWDIy R/W SEN SDATA SCLK GND1 RDx RDy GND3 VCC Rext
48 47 1 2 3 4 5 6 7 46 45 44 43 42 41 40 39 38 37
4Wx
5Ry
5Rx
4Ry
4Rx
36 35 34 33 32
3Ry 3GND 3Rx 3Wy 3Wx
TDA5153X
8 9 10 11 12 13 14 16 15 GND2 31 30 29 28 17 18 19 20 21 22 23 24 25 26 27 0Wx 0Wy 0Rx 0GND 0Ry 1Wx 1Wy 1Rx 1GND 1Ry
MGK421
2Ry 2GND 2Rx 2Wy 2Wx
Fig.3 TDA5153X pad configuration.
1997 Jul 02
9
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
8 8.1 FUNCTIONAL DESCRIPTION Read mode
TDA5153
The read mode disables the write circuitry to save power while reading. The read circuitry is de-activated for write, sleep and standby modes. The read circuitry may also be biased during write mode to shorten transients. The selected head is connected to a multiplexed low-noise read amplifier. The read amplifier has low-impedance inputs nRx and nRy (n is the number of the head) and low-impedance outputs RDx and RDy. The signal polarity is non-inverting from x and y inputs to x and y outputs. Ambient magnetic fields at the MR elements result in a relative change in MR resistance R MR --------------R MR This change produces a current variation R MR I MR = I MR x --------------- , R MR where IMR is the bias current in the MR element. The current variation is amplified to form the read data output signal voltage, which is available at RDx - RDy. AC coupling between MR elements and amplifier stages prevents the amplifier input stages from overload by DC voltages across the MR elements. A fast settling procedure shortens DC settling transients. An on-chip generated stable temperature reference voltage (1.32 V), available at the Rext pin, is dropped across an external resistor (10 k) to form a global reference current for the write and the MR bias currents. The MR bias current DACs are programmed through the serial interface according to the following formula 10 k I MR = ------------------ ( 10 + 16 d4 + 8 d3 + 4 d2 + 2 d1 + d0 ) 2 R ext (in mA), where d4 to d0 are bits (either logic 0 or logic 1). At power-up, all bits are set to logic 0, which results in a default MR current of 5 mA. The adjustable range of the MR currents is 5 mA to 20.5 mA. The MR bias currents are equal for the two stripes of each head. The gain amplifier is 1-bit programmable. The amplifier gain can be set to its nominal value or to the nominal value +3 dB. 8.2 Write mode
read, sleep and standby modes. In write mode, a programmable current is forced through the selected two terminals inductive write head. The push-pull output drivers yield near rail-to-rail voltage swing for fast current polarity switching. The differential write data input WDIx - WDIy is PECL (Positive Emitter Coupled Logic) compatible. The write data flip-flop can either be used or passed-by. In the case that the write data flip-flop is used, current polarity is toggled at the falling edges of the Vdata = VWDIx - VWDIy. Switching to Write Mode initializes the data flip-flop so that the write current flows in the write head from x to y. In the case that the write data flip-flop is not used, the signal polarity is non-inverting from x and y inputs to x and y outputs. The write current magnitude is controlled through on-chip DACs. The write current is defined as follows: 10 k I WR = --------------- ( 20 + 16 d4 + 8 d3 + 4 d2 + 2 d1 + d0 ) R ext (in mA) where d4 to d0 are bits (either logic 0 or logic 1). The adjustable range of the write current is 20 mA to 51 mA. At power-up, the default values d4 = d3 = d2 = d1 = d0 = logic 0 are initialized, corresponding to IWR = 20 mA. IWR is the current provided by the write drivers: the current in the write coil and in the damping resistor together. The static current in the write coil is I WR ---------------- , Rh 1 + -----Rd where Rh is the resistance of the coil including leads and Rd is the damping resistor. 8.3 Sleep mode
To minimize power dissipation, the read circuitry may be disabled in write mode. The write circuitry is disabled in
In sleep mode, the device is accessible via the serial interface. All circuits are inactive, except the circuits of the CMOS serial interface and the circuit which forces the data registers to their default values at power-up and which fixes the DC level of RDx - RDy (required when operating with more than one amplifier). Typical static current consumption is -30 A. Dynamic current consumption during operation of the serial interface in the sleep mode and owing to external activity at the inputs to the serial interface is not included. In all modes including the sleep mode, data registers can be programmed. Sleep is the default mode at power-up. Switching to other modes takes less than 0.1 ms.
1997 Jul 02
10
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
8.4 Standby mode 8.7 Addressing
TDA5153
The circuit can be put in standby mode using the serial interface. In standby mode, typical DC current consumption is 330 A. Transients from standby mode to active mode are two orders of magnitude shorter than from sleep mode to active mode. This is important in the case of cylinder mode operation with multiple amplifiers. All amplifiers can operate from standby mode and all head switch times can be kept just as short as in the case of operation with a single amplifier. Head switching times are summarized in the switching characteristics. 8.5 Active mode
Active mode is either read mode or write mode depending on the R/W pin. 8.6 Bi-directional serial interface
When SEN goes HIGH, bits are latched in at rising edges of SCLK. The first eight bits a7 to a0, starting with a0, are shifted serially into an address register. If SEN goes LOW before 16 bits have been received, the operation is ignored. When more than 16 bits (address and data) are latched in before SEN goes LOW, the first 8 bits are interpreted as an address and the last 8 bits as data. SEN should go HIGH at least 5 ns before the first rising edge of SCLK. Data should be valid at least 5 ns before and after a rising edge of SCLK. The bits a7 to a4 constitute the register address.To validate the communication with the preamplifier, bits a1, a2 and a3 have to be programmed as (1, 0, 0). If bit a0 = logic 0, a programming sequence starts. If bit a0 = logic 1, reading data from the pre-amplifier can start. 8.8 Programming data
The serial interface is used for programming of the device and for reading of status information. 16 bits (8 bits for data and 8 for address) are used to program the device. The serial interface requires 3 pins: SDATA, SCLK and SEN. These pins (and R/W) are CMOS inputs. The logic input R/W has an internal 20 k pull-up resistor and the SEN logic input has an internal 20 k pull-down resistor. Thus, in case the SEN line is opened, no data will be registered and in case the R/W line is opened, the device will never be in write mode. SDATA: serial data; bi-directional data interface. In all circumstances, the LSB is transmitted first. SCLK: serial clock; 25 MHz clock frequency. SEN: serial enable; data transfer takes place when SEN is HIGH. When SEN is LOW, data and clock signals are prohibited from entering the circuit. Three phases in the communication are distinguishable: addressing, programming and reading. Each communication sequence starts with an addressing phase, followed by either a programming phase or a reading phase.
If a0 = logic 0, the last eight bits d7 to d0 before SEN goes LOW are shifted into an input register. Bits d6 and d7 are don't care. When SEN goes LOW, the communication sequence is ended and the data in the input register is copied in parallel to the data register that corresponds to the decoded address a7 to a4. SEN should go LOW at least 5 ns after the last rising edge of SCLK. 8.9 Reading data
Immediately after the IC detects that a0 = logic 1, data from the data register (address a7 to a4) is copied in parallel to the input register. Two wait clock cycles must follow before the controller can start inputting data. At the first falling edge of SCLK after the 2 wait rising edges of SCLK, the LSB d0 is placed on SDATA line followed by d1 at the next falling edge of SCLK etc. If SEN goes LOW before 8 address bits (a7 to a0) have been detected, the communication is ignored.
1997 Jul 02
11
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
TDA5153
handbook, full pagewidth
>5 ns
>5 ns
SEN
SCLK
SDATA
, ,
0
a1
a2
a3
a4
a5
a6
a7
d0
d1
d2
d3 data
d4
d5
d6
,, ,,
d7
MGK423
address
Fig.4 Timing diagram of the serial interface operation; writing sequence (a0 = 0).
handbook, full pagewidth
SEN
SCLK
SDATA
,, ,,
1
a1
a2
a3
a4
a5
a6
a7
address
,, ,,
wait cycles
d0
d1
d2
d3
d4
,, ,,
d5
MGK419
data
Fig.5 Timing diagram of the serial interface operation; reading sequence (a0 = 1).
1997 Jul 02
12
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
8.10 8.10.1 d0 By default (d0 = logic 0), write data passes from the write data input via the data flip-flop to the write driver. The write driver toggles the current in the head at the falling edges of V WDIx - V WDIy V data = ------------------------------------2 When d0 = logic 1, the flip-flop is not used. The signal polarity is non-inverting from WDIx and WDIy to Wx and Wy. d1 By default (d1 = logic 0) the pre-amplifier senses PECL write signals at WDIx and WDIy. d1 should remain logic 0. d2 By default, (d2 = logic 0) the write current is inhibited under low supply voltage conditions. The write current inhibit is made inactive by programming d2 to logic 1. d3 By default (d3 = logic 0), in write mode low supply voltage, open head, and other conditions are monitored and flagged at HUS. If d3 = logic 1, HUS is LOW in write mode and HIGH in read mode. d4 The amplifier read gain may be programmed in the configuration register. By default (d4 = logic 0), the read gain is typically 160 with RMR = 28 . If d4 = logic 1, the read amplifier typical gain is 3 dB higher (i.e. 226 if RMR = 28 ). d5 In order to minimize the write-to-read recovery times, the first stage of the read amplifier may be kept biased during write mode. By default, (d5 = logic 0) the read amplifier is powered-down during write mode, and the fast settling procedure is activated after write-to-read switching. If d5 = logic 1 the read amplifier is kept biased during write mode, and the fast settling procedure still occurs if the head is changed or the MR current is re-programmed. 8.10.2 POWER CONTROL Operation of the serial interface CONFIGURATION
TDA5153
If d1 = d0 = logic 1, the circuit goes in active mode, (read or write mode depending on the R/W input). 8.10.3 HEAD SELECT
d2, d1 and d0 are used to select head H0 to H5 for the 6 channel version and to select head H1 to H4 for the 4 channel version. 8.10.4 SERVO WRITE
The circuit is prepared for servo writing. However, the chip will not be guaranteed. 8.10.5 TEST
d2 = d1 = d0 = logic 0. The circuit is not in test mode. This is the default situation.
8.10.5.1
MR head test
d2 = logic 0, d1 = logic 0, d0 = logic 1. In read mode, the voltages at Rx and Ry (at the top of the MR elements) of the selected head are fed to RDx and RDy outputs. By measuring the output voltages single-ended at two different IMR currents, the MR resistance can be accurately measured according to the following formula: V RDx1 - V RDx2 R MRx = -------------------------------------- for the x side for instance. I MRx1 - I MRx2 Open head and head short-circuited to ground conditions can therefore be detected. d2 = logic 0, d1 = logic 1, d0 = logic 0. Same as before, with the difference that IMR2 is fixed to a minimum constant value of 5 mA. Measuring in the same way as above with IMR1 > 5 mA, enables the detection of MR elements connected together.
8.10.5.2
Temperature monitor
d2 = logic 0, d1 = logic 1, d0 = logic 1. The temperature monitor voltages are connected to RDx and RDy. The output differential voltage depends on the temperature according to: dV = - 0.00364 x T + 1.7 , 0 < T < 140 C The temperature may be measured with a typical precision of 5 C.
By default d0 = d1 = logic 0, the pre-amplifier powers-up in sleep mode. If d1 = logic 0, d0 = logic 1 or d1 = logic 1, d0 = logic 0 the circuit goes in standby mode. 1997 Jul 02 13
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
8.10.5.3 Thermal asperity detector
TDA5153
d2 = logic 1, d1 = don't care, d0 = either logic or 1. Unlike the above tests, the thermal asperity detection does not use the RDx to RDy outputs. Thus, the reader is fully operational. In case a thermal asperity is detected, it is flagged at the HUS pin. The threshold voltage for the thermal asperity detection is 2-bit programmable. These 2 bits consist of d0 (LSB) of the test mode register (address = 0XXX0110), as the MSB, and b2 of the compensation register (address = 0XXX0111). V th = ( 210 + 560 d0 + 280 b2 ) V , where d0 is d0 of test mode register and b2 is d2 of capacitor compensation register. 8.10.6 WRITE AMPLIFIER PROGRAMMABLE CAPACITORS
attenuator provides a pole which limits the bandwidth and reduces the high-frequency noise. The HF pole can be used in combination with the HF zero in order to boost the HF gain locally and yet limit the very high frequency noise enhancement. 8.10.8 HIGH FREQUENCY GAIN BOOST REGISTER
By default (d3 = d2 = d1 = d0 = logic 0), the high frequency gain boost is not active. The gain boost provides a zero which allows to optimize the bandwidth of the read amplifier and to correct for attenuation caused by series inductances in the leads between the MR-heads and the read amplifier inputs. 8.10.9 SETTLE PULSE
By default (d2 = d1 = d0 = logic 0) the programmable capacitors are zero. These capacitors are used to improve the performance of the write amplifier according to the write amplifier output load. 8.10.7 HIGH FREQUENCY GAIN ATTENUATOR POLE
REGISTER
By default (d2 = d1 = d0 = logic 0) the settle pulse has a nominal duration of 3 s. Its value can be programmed from 2.125 s to 3 s according to the following formula: 1 t st = 2 + ------------------------------------------------------------------------- s ( 4 d2 + 2 d1 + 1 d0 + 1 )
By default (d3 = d2 = d1 = d0 = logic 0), the high frequency gain attenuator is not active. The gain 8.10.10 ADDRESS REGISTERS; note 1 A7 A6 A5 A4 A3 A2 A1 A0 0 0 0 0 0 0 1 0 configuration register: d0 = 0: use data flip-flop; d0 = 1: by-pass data flip-flop d1 = 0: the WDI inputs are PECL levels; d1 = 1: invalid d2 = 0: write current inhibit active; d2 = 1: write current inhibit inactive read mode: d3 = 0: HUS active; d3 = 1: HUS HIGH write mode: d3 = 0: HUS active; d3 = 1: HUS LOW d4 = 0: read gain nominal; d4 = 1: read gain nominal + 3 dB d5 = 0: read amplifier OFF during write mode; d5 = 1: read amplifier ON during write mode 0 0 0 1 0 0 1 0 power control register: (d1, d0) = (0, 0): sleep mode (d1, d0) = (1, 0) or (0, 1): standby mode (d1, d0) = (1, 1): active mode (write or read) 0 0 1 0 0 0 1 0 head select register: 6 channels: (d2,d1,d0) = (0,0,0) to (1,0,1): H0 to H5 4 channels: (d2,d1,d0) = (0, 0, 1) to (1, 0, 0): H1 to H4 DESCRIPTION
1997 Jul 02
14
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
A7 A6 A5 A4 A3 A2 A1 A0 0 0 1 1 0 0 1 0 DESCRIPTION
TDA5153
MR current DAC register: 10 k I MR = 0.5 x --------------- x ( 10 + 16 d4 + 8 d3 + 4 d2 + 2 d1 + 1 d0 ) mA R ext write current DAC register: 10 k I WR = --------------- x ( 20 + 16 d4 + 8 d3 + 4 d2 + 2 d1 + 1 d0 ) mA R ext servo write register: (d0, d1) = (0, 0) = one head (d0, d1) = (1, 1) = all heads
0
1
0
0
0
0
1
0
0
1
0
1
0
0
1
0
0
1
1
0
0
0
1
0
test mode register: (d2,d1,d0) = (0,0,0) = not in test mode (d2,d1,d0) = (0,0,1) = read head test (IMR1 = IMR2) (d2,d1,d0) = (0,1,0) = read head test (IMR2 = 5 mA fixed) (d2,d1,d0) = (0,1,1) = temperature monitor (d2,d1,d0) = (1, X, d0) = thermal asperity detection V th = ( 210 + 560 d0 + 280 b2 ) V , see note 2
0 1
1 0
1 0
1 0
0 0
0 0
1 1
0 0
compensation capacitor register: equivalent differential capacitance: ( 4 d2 + 2 d1 + 1 d0 ) x 2 pF high frequency gain attenuator register: 800 MHz nominal pole frequency: -----------------------------------------------------------------------------8 d3 + 4 d2 + 2 d1 + 1 d0
1
0
0
1
0
0
1
0
high-frequency gain boost register: 800 MHz nominal zero frequency: -----------------------------------------------------------------------------8 d3 + 4 d2 + 2 d1 + 1 d0
1
0
1
0
0
0
1
0
settle time register: 1 settle time: t st = 2 + ------------------------------------------------------------------------- s ( 4 d2 + 2 d1 + 1 d0 + 1 )
1
1
1
1
0
0
1
1
chip ID register: ID = 8 d3 + 4 d2 + 2 d1 + 1 d0 , d3 to d0 are preset to (0, 0, 1, 1)
a7
a6
a5
a4
0
0
1
1
when a0 = 1, data from the register with address a7 to a4 is read out on SDATA
Notes 1. Not used bits in the registers (indicated by X) are don't care. Default data, initialized at power-up, is zero in all registers. For VCC < 2.5 V, the register contents are not guaranteed. 2. Vth programming uses both test mode register and compensation capacitor register. d0 in the formula above is the LSB of the test mode register and b2 is the data bit d2 of the compensation register.
1997 Jul 02
15
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
8.11 Head unsafe
TDA5153
The HUS pin is an open-collector output. Consequently, when the pin is not connected to an external pull-up resistor, HUS is LOW. HUS pins can be connected together in case of operation with more than one amplifier. It is used to detect abnormal/unexpected operation. Sleep mode: HUS is HIGH, to permit working with more than one amplifier. Standby mode: HUS is HIGH, to permit working with more than one amplifier. Read mode: * if in the configuration register d3 = 1, HUS is HIGH * if in the configuration register d3 = 0, HUS goes LOW for: - Rext pin open, short-circuited to ground or to VCC (read current too low or too high) - Low VCC and VCC(WD) conditions. A low supply voltage detector is placed close to the VCC and VCC(WD) pins. Detection of low VCC (main general supply): a VCC supply voltage below 4.0 V 5% is flagged to the HUS pin. The voltage detection range is then 4.2 to 3.8 V with an hysteresis of 110 mV 10%. Detection of low VCC(WD) (writer dedicated supply): a fault will be flagged at HUS pin if VCC(WD) drops 0.8 V 10% below VCC. One must be aware that such a detection is only aimed to warn for a catastrophic situation. Indeed, VCC(WD) should never be below VCC. 8.12 HUS survey HUS MODE Sleep mode Standby mode - - Read Active mode Write - - Read mode A-test mode(1) TAS mode Write mode A-test mode(1) Servo mode(2) Notes 1. HUS survey: A-test mode = analog test mode. STATE
Test mode: HUS is HIGH except when the TAS detector is ON. If a thermal asperity is detected, HUS goes LOW. Servo write mode: HUS is LOW Write mode: * if in the configuration register d3 = 1, HUS is LOW * if in the configuration register d3 = 0, HUS goes HIGH for: the write current may be inhibited if d1 = 0 in the configuration register. - Rext pin open, short-circuited to ground or to VCC (write current too low or too high) - Write data input frequency too low (WDIx - WDIy) - Write head Wx - Wy open, Wx or Wy short-circuited to ground (switching to write mode makes HUS LOW; after the transient the HUS detection circuitry is activated; the target for the head-open detect time is 15 ns) - Write-head still left biased while not selected - Low VCC and VCC(WD) conditions (write current inhibit can be active or inactive). The same detector is used for read and write mode. HUS goes LOW again between 0.5 and 1 s after the last unsafe condition was detected.
DATA BIT D3 0 HIGH HIGH ACTIVE HIGH ACTIVE ACTIVE HIGH LOW HIGH HIGH HIGH HIGH ACTIVE LOW HIGH LOW 1
2. In servo mode, the performance of the IC is not guaranteed.
1997 Jul 02
16
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
9 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VCC VCC(WD) VIL VIH Vn1 supply voltage write driver supply voltage LOW level digital input voltage HIGH level digital input voltage voltage on all pins except VCC, read inputs nRx, nRy and write outputs nWx, nWy (n = 0 to 9) but not higher than Vn2 Vn3 InGND Tstg Tj voltage on write driver outputs nWx, nWy but not higher than voltage on read inputs nRx, nRy current through pins nGND storage temperature junction temperature PARAMETER -0.5 -0.5 -0.5 -0.5 -0.5 - -0.5 - -0.5 - -65 - MIN. MAX. +6.0 +9.5 +5.5 +5.5 +5.5 VCC + 0.5 +8.8 1 0.1 +150 150
TDA5153
UNIT V V V V V V V V A C C
VCC(WD) + 0.8 V
10 HANDLING Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is desirable to take normal precautions appropriate to handling MOS device. 11 THERMAL CHARACTERISTICS SYMBOL Rth j-a PARAMETER thermal resistance from junction to ambient TDA5153AG, TDA5153BG TDA5153X Note 1. The TDA5153X is shipped in naked dies. The thermal resistance depends on the flex used. in free air 70 see note 1 K/W CONDITION VALUE UNIT
1997 Jul 02
17
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
12 RECOMMENDED OPERATION CONDITIONS SYMBOL VCC VCC(WD) VIH VIL Vi(dif)(p-p) VIH(PECL) VIL(PECL) Tamb Tj RMR RMR Ll(tot) Rl(tot) VMR PARAMETER supply voltage range write driver supply voltage HIGH level input voltage (CMOS) LOW level input voltage (CMOS) differential input voltage (peak-to-peak value) HIGH level PECL input voltage LOW level PECL input voltage ambient temperature junction temperature MR element resistance RMR mismatch total lead inductance to the head total lead resistance to the head voltage on top of MR elements note 4 in each lead; note 5 in each lead; note 5 note 6 reading writing (VCC(WD) = 8 V) note 3 note 3 note 3 CONDITIONS note 1 note 2 MIN. 4.5 VCC 3.5 0 0.4 1.5 - 0 - - 15 - - - - 0.4 including lead; note 5 including lead; note 5 including lead; note 5 V ref I ref = ---------R ext - - - - - - - - 0.7 2.85 2.15 - - - 28 - 35 1.5 - 1 0.15 10 5 10 TYP
TDA5153
MAX. 5.5 8.8 VCC 0.8 1.5 VCC - 70 110 130 34 4 - - 0.5 2 - - - - V V V V V V V
UNIT
C C C nH V mV H pF k
Vsig(dif)(p-p) differential MR head input signal (peak-to-peak value) Lwh Rwh Cwh Rext write head inductance write head resistance write head capacitance external reference resistor
Notes 1. A supply by-pass capacitor from VCC to ground or a low-pass filter may be used to optimize the PSRR. 2. The supply voltage VCC(WD) must never be below VCC in normal mode, and two diode voltages above VCC in servo mode. 3. The given values should be interpreted in such a way that the single-ended voltage could swing 0.2 to 0.75 V and that the common mode voltage should be such that for any of the two states, VIH(max) < VCC and VIL(min) > 1.5 V. PECL voltage swing: a wider peak-to-peak voltage swing can be used. In that case a current will flow through the ( WDIx - WDIy ) - 1.4 WDI inputs. This current is approximately equal to ---------------------------------------------------------200 4. The mismatch refers to the resistance of the two stripes of the same head. This is defined as follows: RMR = RMR1 - RMR2 5. These parameters depend on the head model. The values given are those used for testing. 6. The combination of maximum head resistance, lead resistance and bias current is not permitted. To avoid voltage break-through between heads and disk, the voltage over the MR elements is limited by two diodes.
1997 Jul 02
18
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
13 CHARACTERISTICS VCC = 5.0 V; VCC(WD) = 8 V; VGND = 0 V; Tamb = 25 C; unless otherwise specified. SYMBOL Read characteristics IMR IMR MR current adjust range tolerance (excluding Rext) I MR - I MR(PR) --------------------------------I MR(PR) with IMR(PR) = 10 mA Gv(dif) differential voltage gain; note 1 from head inputs to RDx, RDy; RMR = 28 ; IMR = 10 mA; f = 20 MHz; d4 = 0 d4 = 1 Ri(dif) Ci(dif) THD BL BH F Vnir fB(L) differential input resistance differential input capacitance total harmonic distortion signal gain pass band edge; note 2 -3 dB signal gain pass band edge without -3 dB (4 nH lead inductance) gain boost; note 2 -3 dB (50 nH lead inductance) noise figure; note 3 RMR = 28 ; IMR = 10mA; Tamb = 25 C; f = 20 MHz IMR = 10 mA - - - - - - - - - - - 160 226 13 16 1 - 220 170 3.0 0.9 Rext = 10 k; 0.5 mA steps 5 - - 4 PARAMETER CONDITIONS MIN. TYP.
TDA5153
MAX.
UNIT
20.5 -
mA %
- - - - - 100 - - 3.2 1.0 400 pF % kHz MHz MHz dB nV/Hz kHz
input referred noise voltage; note 3 RMR = 28 ; IMR = 10mA; Tamb = 25 C; f = 20 MHz +3 dB noise low corner frequency RMR = 28 ; IMR = 10 mA; Tamb = 25 C; no lead inductance RMR = 28 ; IMR = 10 mA; Tamb = 25 C; no lead inductance unselected head f < 100 MHz; IMR = 10 mA
fB(H)
+3 dB noise upper corner frequency channel separation; note 4
-
220
MHz
cs PSRR CMRR
- - -
50 80 50
dB dB dB
power supply rejection ratio; note 5 f < 1 MHz; IMR = 10 mA common mode rejection ratio; note 5 from nRx - nRy to RDx - RDy; RMR mismatch < 5%; IMR = 10 mA; f < 1 MHz f < 100 MHz
- -
45 25 50 - 16 0.2 -
dB dB dB V
DR VO(R)(dif) Zo(R)
rejection of SCLK and SDATA; note 6
from SCLK, SDATA inputs to - the RDx - RDy outputs; note 7 - -
output DC offset voltage in read DC voltage between mode (differential after DC settling) RDx - RDy (in read mode) output impedance in read mode single ended
1997 Jul 02
19
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
SYMBOL Io(max)(dif) Vo(cm) V ocm ---------------V CC Zo(n)(dif) PARAMETER maximum differential output current common mode output voltage in read mode common mode DC supply rejection in read mode differential output impedance in other modes (write, standby, sleep) RDx, RDy CONDITIONS MIN. - 1.0 - - TYP. 4 1.5 20
TDA5153
MAX. - 2.0 - -
UNIT mA V dB
50
k
Write characteristics IWR IWR write current adjust range (in the write drivers) tolerance (excluding Rext); I WR - I RW (PR) ----------------------------------I RW (PR) Vs(max)(p-p) Ro(dif) tr, tf maximum voltage swing (peak-to-peak value) differential output resistance write current rise/fall time without flip-flop (10% to 90%); note 8 write current asymmetry; note 9 propagation delay 50% of (WDIx/WDIy) to 50% of (Wx, Wy) channel separation VCC(WD) = 8 V; Lh = 150 nH, Rh = 10 ; IWR = 35 mA; f = 20 MHz percentage of tr/tf (tr, tf and logic asymmetry) write head short circuited; data flip-flop by passed unselected head VCC(WD) = 5 V VCC(WD) = 8 V (differential) - - - - - - 200 - 8 13 - 1.8 V V ns Rext = 10 k; 1 mA steps IWR(PR) = 35 mA 20 - 35 7 51 - mA %
tas tpd cs fSCLK Vo(cm) trec(W-R)
- - - -
- - 45 - 200
5 5 -
% ns dB
Switching characteristics serial interface clock rate output common mode DC voltage change from Read to Write modes write to read recovery time (AC and DC settling); note 10 IMR = 10 mA; IWR = 35 mA from 50% of the rising edge of R/W to steady state read-back signal: AC and DC settling at 90% (without load at RDx - RDy) read amplifier OFF: d5 = 0 read amplifier ON: d5 = 1 tsw(R) head switching (in read mode), standby to read active and MR current change recovery time; (AC and DC settling); note 11 read amplifier off time from falling edge of SEN to steady state read-back signal; (without load at RDx - RDy) from falling edge of R/W to read head inactive - - - 3 100 3 4.5 150 4.5 s s s 25 - MHz mV -
toff(R)
-
-
50
ns
1997 Jul 02
20
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
SYMBOL tst(W) PARAMETER write settle times; note 12 CONDITIONS MIN. TYP. -
TDA5153
MAX. 70
UNIT ns
from 50%of the falling edge of - R/W to 90% of the steady state write current (in Write Mode) from rising edge of R/W to IWR-programmed /10 (IWR = 35 mA) from falling edge of SEN to write head active -
toff(W)
write amplifier off time
-
50
ns
tsw(W) tsw(S)
head switching (in write mode), and standby to write head active sleep to (and from) any other modes
- -
50 -
70 100
ns s
DC characteristics ICC(R) ICC(W) supply current; note 13 supply current; note 14 read mode; IMR = 10 mA write mode; IWR = 35 mA from VCC (5 V) from VCC(WD) (5 to 8 V) IDD(stb) IDD(S) Vref standby mode supply current sleep mode supply current reference voltage for Rext static - - - - - 33 54 0.25 0.025 1.32 41 61 1 - - mA mA mA mA V - 72 80 mA
Notes to the characteristics 1. The differential voltage gain depends on the MR resistance. It can be improved by programming the d4 bit in the configuration register using the serial interface. 2. The gain boost implements a pole-zero combination: The +3 dB gain boost corner frequency is 800 MHz ------------------------------------------------------------------------------------( 8 d3 + 4 d2 + 2 d1 + 1 d0 ) The -3 dB gain attenuation corner frequency is 800 MHz ------------------------------------------------------------------------------------( 8 d3 + 4 d2 + 2 d1 + 1 d0 ) where d3, d2, d1, d0 are bits (0, 1) to be programmed via the Serial Interface. In practical use, the bandwidth is limited by the inductance of the connection between the MR heads and the pre-amplifier. 3. Noise calculation a) Definitions: The amplifier has a low-ohmic input. No lead resistance is taken into account. The input referred noise voltage, excluding the noise of the MR resistors, is defined as follows: V no 2 2 V nir = -------- - 4kT x ( R MR1 + R MR2 ) V Gv where Gv is the voltage gain and Vno is the noise voltage at the output of the amplifier, k is the 1997 Jul 02 21
Boltzmann constant and T is the temperature in K. The noise figure is defined as follows: V no 2 -------- Gv F = 10 x log ----------------------------------------------------------- dB 4kT x ( R MR1 + R MR2 ) in 1 Hz bandwidth. Note that RMR includes all resistances between Rx or Ry to ground. b) Noise figure versus IMR and RMR: Table 1 shows the variation of the noise figure with IMR (mA) and RMR (). c) Input noise voltage consideration: the input referred noise voltage calculation can significantly be different (from 1.0 to 0.44 nV/Hz for instance) by taking into account an equivalent signal-to-noise ratio when using two MR stripes (28 for each stripe) or one MR stripes (42 W). It assumes that the signal coming from the head is larger for a dual stripe head than for a single stripe head (50% extra signal for dual stripe head). 4. The channel separation is defined by the ratio of the gain response of the amplifier using the selected head H(n) to the gain response of the amplifier using the adjacent head H(n 1), Head H(n) being selected.
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
5. The PSRR (in dB) is defined as input referred ratio: Gv PSRR = 20 x log ------ Gp Where Gv is the differential input to differential output gain, and Gp is the power supply to differential output gain. The CMRR (in dB) is defined as input referred Gv ratio: CMRR = 20 x log ---------- G cm where Gv is the differential input to differential output gain and Gcm is the common mode input to differential output gain. Flex and board lay-out may affect significantly these parameters. 6. This refers to the crosstalk from SCLK and SDATA inputs via the read inputs to RDx - RDy. Two cases can be distinguished: a) With SEN LOW, SCLK and SDATA are prohibited from entering the device and crosstalk is low. b) Programming via the serial interface is done with SEN HIGH. Then crosstalk can occur. A careful design of the board or flex-foil is required in order not to get crosstalk via this path. 7. A 200 mV peak-to-peak signal is applied to SCLK or SDATA inputs at 25 MHz, and measurement is performed at RDx - RDy. Table 1 Noise figure F (dB) RMR () 20 25 30 IMR = 7 mA 2.7 2.8 2.9 IMR = 10 mA 2.9 3.0 3.1
TDA5153
8. The rise and fall times depend on the write amplifier-write head combination. Lh and Rh represent the components on the evaluation board. Parasitic capacitances also limit the performance. 9. The write current rise/fall time asymmetry is defined by tr - tf ---------------------2 ( tr + tf) 10. Write-to-read recovery time includes the write mode to read mode switching using the R/W pin on the same head (see Fig.6). The AC signal reaches its full amplitude few tenth of ns after appearing at the reader RDx and RDy outputs. 11. In read mode, the head switching, standby to read active switching and changing MR current include fast current settling (see Fig.7). Same note regarding the AC signals at the reader outputs as above. 12. Write settle time includes read mode to write mode switching using the R/W pin. 13. The typical supply current in read mode depends on the bias current for the MR element. 14. The typical supply current in write mode also depends on the write current.
IMR = 15 mA 3.1 3.3 3.5
1997 Jul 02
22
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
TDA5153
handbook, full pagewidth
R/W
RDx-RDy
trec(W-R)
toff(R)
MGG985
Fig.6 Timing diagram of the reader: write-to-read switching on the same logic head.
handbook, full pagewidth
SEN
RDx-RDy
tsw(R)
MGG986
Fig.7 Timing diagram of the reader: typical head, current and standby-to-read characteristics.
1997 Jul 02
23
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
14 PACKAGE OUTLINE LQFP48: plastic low profile quad flat package; 48 leads; body 7 x 7 x 1.4 mm
TDA5153
SOT313-2
c
y X
36 37
25 24 ZE
A
e
Q E HE A A2 A1 (A 3) Lp L detail X
wM pin 1 index 48 1 12 ZD bp D HD wM B vM B vM A 13 bp
e
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.60 A1 0.20 0.05 A2 1.45 1.35 A3 0.25 bp 0.27 0.17 c 0.18 0.12 D (1) 7.1 6.9 E (1) 7.1 6.9 e 0.5 HD 9.15 8.85 HE 9.15 8.85 L 1.0 Lp 0.75 0.45 Q 0.69 0.59 v 0.2 w 0.12 y 0.1 Z D (1) Z E (1) 0.95 0.55 0.95 0.55 7 0o
o
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT313-2 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION
ISSUE DATE 93-06-15 94-12-19
1997 Jul 02
24
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
15 SOLDERING 15.1 Introduction
TDA5153
If wave soldering cannot be avoided, the following conditions must be observed: * A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. * The footprint must be at an angle of 45 to the board direction and must incorporate solder thieves downstream and at the side corners. Even with these conditions, do not consider wave soldering LQFP packages LQFP48 (SOT313-2), LQFP64 (SOT314-2) or LQFP80 (SOT315-1). During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Maximum permissible solder temperature is 260 C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 C within 6 seconds. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. 15.4 Repairing soldered joints
There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). 15.2 Reflow soldering
Reflow soldering techniques are suitable for all LQFP packages. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 C. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 C. 15.3 Wave soldering
Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C.
Wave soldering is not recommended for LQFP packages. This is because of the likelihood of solder bridging due to closely-spaced leads and the possibility of incomplete solder penetration in multi-lead devices.
1997 Jul 02
25
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
16 DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values
TDA5153
This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. 17 LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
1997 Jul 02
26
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD) with MR-read/inductive write heads
NOTES
TDA5153
1997 Jul 02
27
Philips Semiconductors - a worldwide company
Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 689 211, Fax. +359 2 689 102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S, Tel. +45 32 88 2636, Fax. +45 31 57 0044 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615800, Fax. +358 9 61580920 France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex, Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 23 53 60, Fax. +49 40 23 536 300 Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS, Tel. +30 1 4894 339/239, Fax. +30 1 4814 240 Hungary: see Austria India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd. Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722 Indonesia: see Singapore Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3, 20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108, Tel. +81 3 3740 5130, Fax. +81 3 3740 5077 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA, Tel. +48 22 612 2831, Fax. +48 22 612 2327 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000, Tel. +27 11 470 5911, Fax. +27 11 470 5494 South America: Rua do Rocio 220, 5th floor, Suite 51, 04552-903 Sao Paulo, SAO PAULO - SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 829 1849 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 3 301 6312, Fax. +34 3 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 632 2000, Fax. +46 8 632 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2686, Fax. +41 1 481 7730 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Talatpasa Cad. No. 5, 80640 GULTEPE/ISTANBUL, Tel. +90 212 279 2770, Fax. +90 212 282 6707 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 (c) Philips Electronics N.V. 1997
Internet: http://www.semiconductors.philips.com
SCA54
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
297027/25/01/pp28
Date of release: 1997 Jul 02
Document order number:
9397 750 01904

▲Up To Search▲

Price & Availability of TDA5153AG

	To Download TDA5153AG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .